English translation for "meshing point"

啮合点

Related Translations:

nylon mesh:  尼龙网布尼龙网眼花边

mesh weld:  网状焊缝压边焊接焊缝

geographic mesh:  经纬线网

displace mesh:  位移网格

meshed welding:  搭接压焊

stretched mesh:  拉直网目

mesh socks:  网眼袜

wireless mesh:  无线网状网

mesh networking:  网状网络

mesh type:  网格类型

Example Sentences:

	1.	The mesh points are numbered with index k in the order in which the unknowns are considered . 网格点按所考虑的未知量以脚标k来计数。
	2.	In surface high grinding , adapts mesh point high accuracy big area printing 回答5 .表面中高磨削,适应网点高精度大面积印刷
	3.	Study of load - bearing capacity for single - layer cable mesh point - supporting glass curtain 单层索网点支式玻璃幕墙的承载性能研究
	4.	By looking through a face on the target mesh , as if it where a window , you should be able to see every polygon on your source mesh pointing more or less in your direction 通过察看目标网格上的一个面，比如窗户那里的面，你将可以看到在你源网格的每一个多边形或多或少的指向你的方向。
	5.	Equipped with four - color and mesh point overprint , multi purpose ( also can be used for the single or consecutive printing for trade mark ) ; it substitutes the traditional troublesome craft , reducing the production cost greatly 该机以印带糊、四色印刷；一机多用，可用于单张或连续商标印刷；代替传统烦琐工艺，大幅降低成本。
	6.	Presently is equipped with the department of commercial affairs , the engineering dept , the mechanical and electrical service service department , welds shears the technological exchange department , has set up many service mesh point in hubei 现设有商务部，工程部，机电维修服务部，焊割技术交流部，并已在湖北开办多家服务网点。
	7.	The other is based on contour line . the way is that first editing the contour line , then saving these heights , finally depending on linear calculating middle value , thus getting the height of every mesh point , and the 3d terrain model 另一种方法是基于等高线的方法，该方法是通过对等高线进行编辑，保存相应点的高程，再根据线性插值，得到各个网格点的高程，从而生成对应的地形模型。
	8.	As both the meshing point and ball ' s center are on the given cylinder , a general method for developing the cam ' s profile is studied . it is proved that the profile of positive and negative transmission is unique if the face gear , the difference between face tooth number and ball number and the diameter of ball are the same . the concrete expression of meshing cam on given spatial cycloid profile , and the characteristics of the profiles are discussed 论文的主要工作包括： 1 、根据啮合点和钢球中心轨迹均在同一圆柱面上的特点，研究了给定端齿齿廓条件下求解凸轮齿廓的一般方法；论证了在给定端齿、齿差数和钢球直径相同的条件下，正负齿差啮合齿廓的唯一性；讨论了端齿为球面摆线时，凸轮齿廓的具体表达式，并研究了该齿廓的性质。

Similar Words：

"meshing gear" English translation, "meshing interference" English translation, "meshing model" English translation, "meshing needle" English translation, "meshing nets" English translation, "meshing size" English translation, "meshing solenoid" English translation, "meshing test" English translation, "meshino" English translation, "meshiri" English translation